MENUPRICE REDUCTIONS
- Computer Network Accessories
-
- » ANALOG SENSORS#08391
Vibration detector (Vutlan VT540)
Sensor made for remote monitoring of vibration of the elements its attached to.
- » ADDITIONAL ACCESORIES#08370
Magnet access sensor (Vutlan KMS-30)
The sensor made for checking whether the doors or windows have been opened/closed.Installation Insert the terminal into "Dry contact Input" of Vutlan monitoring system. Supply includes magnet sensor,
4x screws M3 12.5mm,
2x stickers.Max. distance 500m Power consumption 6W Dimensions (WHL) Two 60x18x18mm compact devices
#03120Modbus RTU Slot Extension (Vutlan VT485m)
Allows to monitor up to 32 Modbus RTU devices/meters/sensors. The maximum distance of a daisy chain is up to 1000 meters. Each metered value of a Modbus device is addressed individually using input registers and is shown by the system as virtual sensors. You can configure thresholds and icon representations for these elements.
It can be used with VT335t, VT336t, VT825t, and VT855t monitoring systems. A slot PCB board can be inserted inside the monitoring unit while the unit is in operation. Has an internal termination and by default, it is switched ON (if required can be turned off).
#03127Rechargeable backup battery (Vutlan VT-ACCU)
Rechargeable backup battery is an extension module that can be purchased separately. It is used for VT604t, VT825t, and VT855t. While in operation, the batteries are charged. If the power input drops. The unit will detect a voltage drop and work from VT-ACCU rechargeable batteries until the batteries are discharged.
#03152RJS3 10m AWG24 6P4C straight cable
Patch cable for analog & CAN sensors, unshielded, 10m
#03150RJS3 3m AWG24 6P4C straight cable
Patch cable for analog & CAN sensors, unshielded, 3m
#03151RJS3 5m AWG24 6P4C straight cable
Patch cable for analog & CAN sensors, unshielded, 5m
#08204USB100 / USB dome camera
USB UVC/MJPEG digital camera with high resolution and with IR Leds for direct connection to the VUTLAN system controller.
It allows to view the monitored room on an ongoing basis as well as send a video sequence to an email address in response to a defined event.
In addition, the camera connected to the VUTLAN controller is visible in the network at a dedicated URL, allowing to capture the video stream just like from an IP camera (MJPEG stream).HARDWARE FEATURES: Interface USB format(Complies with USB 2.0 CAMERA: Image Sensor 1/4" Color CMOS H62 Resolution 1.0 Megapixel (640 x 480) Minimum Illumination 0.01 Lux @ F1.2 VIDEO/IMAGE: Video Compression MJPEG Frame Rate & Resolutions Max. 20 fps at 640x480 (VGA),
Max. 20 fps at 320x240 (QVGA)Video Streaming Controllable Frame Rate OTHERS: Cable lenght 5m Operating Temperature 0°C∼ 40°C (Humidity 0% RH∼ 80% RH) Weight 550g
#03128VT-BAT / Reservation battery 9V
"VT-BAT / Reservation battery 9V" keeps the device operational while the main power source is disabled. The device uses a non-rechargeable 6F22 9V lithium battery. The Vutlan monitoring system may work from this battery for approximately 1 to 10 hours.
A 9V is not included. You can use a 9V battery enclosed in a standard PP3 enclosure.
#03121VT485r / OSDPv2 Reader Extension
Allows to connect readers, and keypads with OSDP protocol support. It is an extension PCB board and should be purchased separately.
It can be used with VT335t, VT825t, and VT855t monitoring systems. VT485r can be inserted inside the monitoring unit while the unit is in operation. VT485r has internal termination and by default, it is switched ON (if required can be turned Off).
Allows to connect SE mini reader, SE keypad, and any other 3rd party OSDP readers or keypads.
-
Page 2 of 2
|
